New Trends in Natural Stone

• Got the Magma Supreme granite peninsula on the CNC now. Starting with some slots for both steel and fiberglass reinforcement. #
• Cut a some wine room counters out of polished Sea Foam Green granite. #
• Now cutting the kitchen counters out of the same Seafoam Green granite. #
• Hand finishing the Magma Supreme granite perimeter countertops. #

Powered by Twitter Tools

• Working on a program for a cooktop cutout & Italian edge detail on a Magma Supreme granite peninsula. #
• Just ran the 3rd pc of Magma Supreme granite with an Italian edge detail (ran 1st 2 yesterday), setting up for the 4th pc now. #
• Cutting the last 2pc of the Finnish Soapstone on the saw. #
• Stunning Magma Supreme for a kitchen countertop. http://t.co/o4nd1O5I #
• Running a @EclipseSinks Diablo 501R under-mount sink cutout in the leathered Finnish Soapstone now. #

Powered by Twitter Tools

• Back down to Franktown, CO with another truck load of countertops 2 install. A 2nd island & 4 vanities. This will finish up the job. #
• Got the hose clamp I need to fix a bad water hose (trimmed off a good 10″ from the end). #
• Re-honing a couple pieces of Belgium Bluestone for some tops in Evergreen. #
• Programming the Italian edge detail on some more pieces of the Magma Supreme granite countertops. #
• Running the Franke PRX 120 under-mount sink cutout & Italian edge detail on a piece of Magma Supreme granite. #
• Cutting a leathered Finnish Soapstone kitchen. This is one of our Slab Packages -> http://t.co/mMyPsdfG #

Powered by Twitter Tools

• TGIF! #
• Running the last of the @Kohler 2339 Memoir under-counter sink cutouts now. This is a double sink honed Belugia limestone vanity. #
• Putting some reinforcing ½” sq steel tubing in the 3cm Magma Supreme granite peninsula now. #
• Installing some countertops down in Franktown, CO today. Will have another day down there (same job site) next week. #
• Polishing the backside (exposed overhang) of the seating bar portion of the Magma Supreme granite peninsula. #
• Working on programming a Franke PRX 120 sst under-mount sink cutout in the Magma Supreme granite. #

Powered by Twitter Tools

• Started the morning off with snow removal. Its a wet heavy snow. #
• Loading the install truck, while waiting for a call from the homeowner if we can even get to the house in Franktown. #StillSnowing #
• Running the Hillsboro limestone piece on the CNC for the Mirabella MIRUC309 sst under-mount sink. #
• Running the 1st of many @Kohler 2339 Memoir under-counter sink cutouts. The 1st 2 are in a honed Pietra Lavica schist double vanity. #
• Making some more vinyl templates. #
• Doing a Full Bullnose on the last piece of honed Belugia limestone. This one will get 2 @Kohler 2339 Memoir under-counter sinks. #
• Cutting some Belgium Bluestone for a job in Evergreen. #
• Hand finishing the hone Pietra Lavica schist kitchen countertops. #
• Hillsboro Limestone getting a sink cutout. http://t.co/tssa8rlH #
• http://t.co/V7rAj7AI #
• Setting-up for the 2nd honed Pietra Lavica schist vanity. This one is a single & it too is getting a @Kohler 2339 Memoirs under-mount sink. #
• Cutting the 1st of 3 slabs of Magma Supreme granite for a kitchen. These countertops will be getting an Italian edge detail. #

Powered by Twitter Tools

• Got the Pietra Lavica schist island loaded into the CNC to run the @blancoamerica 441128 under-mount sink cutout. #
• Doing a 4cm Full Bullnose edge detail on some vanity countertops of honed Belugia limestone on R @parkindustries Pro Edge III. #
• Programming a Mirabella MIRUC309 under-mount sink cutout in a piece of honed Hillsboro limestone. #

Powered by Twitter Tools

• Installed a new water flow sensor in R CNC. Hope this fixes the problem. #fingersCrossed #maintenance #
• Doing a Full Bullnose edge detail on a piece of honed Belugia limestone on R @parkindustries Pro Edge III #
• Programming a @blancoamerica 441128 sink cutout in a honed Pietra Lavica schist island countertop. #
• The revised “Block Sink Machining Process” page & slideshow just went live -> http://t.co/XYktOExj #WebDesign #SEO #gallery #pix #photos #

Powered by Twitter Tools

• Programming a @blancoamerica 440194 under-counter kitchen sink cutout in a piece of honed Belugia limestone with a Chiseled edge detail. #
• Did a slab layout with a customer, working with another customer on selecting edge details http://t.co/HehGfAkR #
• honing the face a couple of piece of 2cm Belugia limestone that have shop joints. #
• Happy President’s Day! #

Powered by Twitter Tools

• TGIF! #
• Running the last piece of Cosmos now, then a couple pieces of Belugia limestone to be run on the CNC. #
• Got the 1st half of the Belugia limestone island off the CNC just before lunch, got the 2nd half on now. #
• Re-honing pieces of Pietra Lavica now. #
• Chiseling the edge on a couple more pieces of Belugia limestone. #
• Plotting some vinyl templates for a customer layout. #

Powered by Twitter Tools

• Running an OG edge on some Cosmos (beautiful, but flaky soft don’t even call it a granite) material. Very much a pain to work with… #
• The updated Sink slideshow just went live -> http://t.co/YrY4o3oi dropped one bad photo & added 5 new ones. #WebDesign #SEO #
• Re-honing some more pieces of Belugia limestone. #
• Garage door is fixed. #maintenance #
• Gluing up a couple of shop joints on some of the 2cm Belugia limestone countertops. #
• Just finished programming the second half of the honed Belugia limestone. Will run both pieces tomorrow (sink cutout & cooktop cutout). #
• 1 piece of Cosmos left to run tomorrow. No problems with the 3 pieces we ran today. Whew! #

Powered by Twitter Tools