Subscribe

2 February 2012

Twitter Updates for 2012-02-02

Filed under: Counter Tops,Granite,Limestone,Production Updates,Sinks,Texturing — Tags: , , , — Mike Michaelson @ 23:55 MST
  • Still running pieces of the Golden Crystal #granite on the @parkindustries Pro Edge III. Also starting on the @elkayusa sink cutout program. #
  • Leathering a partial slab of limestone, turned out the full slab was not quite big enough for all the pieces we need to cut. #

Powered by Twitter Tools

Share

31 January 2012

Twitter Updates for 2012-01-31

Filed under: Granite,Limestone,Marble,Production Updates,Texturing — Tags: , , , , — Mike Michaelson @ 23:55 MST
  • Cut a piece of Tan Brown #granite this morning, now polishing the edge on the @parkindustries Pro Edge III. #
  • Re-polished a piece of Calcutta Gold #marble for a table. Will be putting it on the CNC shortly for a OG Bullnose edge detail. #
  • Got a pile of returned flyers for @PercocoSFC St. Valentine’s special. #
  • Getting ready to leather a limestone slab… #

Powered by Twitter Tools

Share

21 December 2011

Twitter Updates for 2011-12-21

Filed under: Bath,Counter Tops,Granite,Marble,Production Updates,Texturing — Tags: , , , , , — Mike Michaelson @ 23:55 MST
  • Installing the #leathered Seafoam Green #granite bathroom pcs today in Evergreen. It consists of a vanity, u/m tub deck, shelf & wall caps. #
  • Touching up the edge of the 6′ dia table that is normally in our showroom. Will put it back once the floor is done being re-polished. #
  • Programming a Villeroy & Boch Evana 6147 00 under-mount sink cutout in polished Negro Marquina #marble Edge detail is a 1″x¾” Bevel. #

Powered by Twitter Tools

Share

20 December 2011

Twitter Updates for 2011-12-20

  • Ground, cleaned & honed the shop office floor yesterday, sealed it this morning. Showroom floor is next. #
  • Ran a CAT5e cable from R wiring closet 2 where the copier goes. New copier is network ready. Hope 2 get it this week, but it might B next. #
  • Re-polishing the Ø6′ Ubatuba/Blue Bahia table that is normally in R showroom. Had to move it to work on the floor, so… #
  • Hand finishing on the #leathered Seafoam Green #granite vanity & tub deck that we will be installing tomorrow in Evergreen. #
  • Working on piece of 2cm Negro Marquina #marble It is a 3pc powder bath with a raised center. Gluing the build-up strips on the edges now. #

Powered by Twitter Tools

Share

19 December 2011

Twitter Updates for 2011-12-19

Filed under: Bath,Counter Tops,Finishing,Granite,Production Updates,Sinks,Texturing — Tags: , , — Mike Michaelson @ 23:55 MST
  • It’s the week before Christmas. Do you have all your holiday shopping done? How about those projects around the house before company comes? #
  • Running the #leathered Seafoam Grean #granite under-mount tub cutout on the CNC. Finishing the program 4 the matching vanity sink cutouts. #
  • Drove to Boulder, did a template & drove back already this morning. #

Powered by Twitter Tools

Share

8 November 2011

Twitter Updates for 2011-11-08

  • Honeing the edges of a piece of Pietra de Cardoso #schist for a upper bar top in Crested Butte. #
  • Installing the Polar White #marble medicine cabinets today. #
  • Templating a kitchen today. #
  • Bush hammering a partial slab of Black Absolute #granite 4 stair treads. Other part of slab is remaining polished 4 stair risers. #
  • Honing the edges of the #honed White Peracima #granite countertops that we cut yesterday. #
  • Programming SCO in the #honed White Peracima #granite L-shaped countertop. #
  • Hand finishing the Juperana Santa Cecilia #granite Working on the ¼” Double Bevel edge detail. #

Powered by Twitter Tools

Share

28 February 2011

Twitter Updates for 2011-02-28

Filed under: Counter Tops,Finishing,Granite,Kitchen,Marble,Production Updates,Sinks,Texturing — Tags: , , , — Mike Michaelson @ 17:00 MST
  • running the last pc of #Ghibli granite with a sink cut out. Still have 2 radiused upper bar tops to run on the CNC. #
  • As I will be gone the rest of the week hopefully someone else will get on here once or twice a day… #
  • I think I figured out (and corrected) at least one of the things happening with #twittertools #
  • For more information about specialty finishes for #granite and #marble please see http://prcc.us/eu3AHj #
  • Making more samples of the #Scarpaletto (fine and coarse) and the #Rake (fine and coarse) finishes for Percoco Stone Finishing sample boards #
  • Running #Ghibli #granite tops on the CNC today. #

Powered by Twitter Tools

Share

9 February 2011

Working on making samples of o…

Filed under: Finishing,Marble,Production Updates,Texturing — Tags: , — Mike Michaelson @ 09:21 MST

Working on making samples of our (#Percoco) specialty finishes in White Carrara. #Rake & #Scarpaletto for Percoco Stone Finishing Center.

Share

13 October 2008

Percoco Stone Finishing Center Now open for business!

Filed under: Finishing,Natural Stone,Texturing — Tags: , , — Mike Michaelson @ 09:32 MST

Our new location for slab finishing (Percoco Stone Finishing Center) is now open for business. We will now do all slab finishing there, rather than at our fabrication shop (except for finishing on our own fab jobs).

Percoco Stone Finishing Center is located at:

730 S Jason St, Unit 11
Denver, CO 80223
303-733-3045
303-733-2957 FAX

Hours of operation are 7:30am – 4:00pm M-F.

Share

31 July 2008

New Machines Coming!

Filed under: Finishing,Natural Stone,Texturing — Tags: , — Mike Michaelson @ 08:00 MST

Both our new finishing machines have shipped and we will be installing them in our new location the first half of September. Once we have the first one up and running, we will begin operating Percoco Stone Finishing Center Denver out of the new location. Percoco Marble will stay at the current location. This will significantly increase our production of slab finishing and should decrease lead time significantly for slabs. This move should also benifit the fab shop by allowing us to concentrate on fabrication and freeing up the machine here for use on our fab jobs.

Share
Older Posts »