New Trends in Natural Stone

• Got the Pietra Lavica schist island loaded into the CNC to run the @blancoamerica 441128 under-mount sink cutout. #
• Doing a 4cm Full Bullnose edge detail on some vanity countertops of honed Belugia limestone on R @parkindustries Pro Edge III. #
• Programming a Mirabella MIRUC309 under-mount sink cutout in a piece of honed Hillsboro limestone. #

Powered by Twitter Tools

• Installed a new water flow sensor in R CNC. Hope this fixes the problem. #fingersCrossed #maintenance #
• Doing a Full Bullnose edge detail on a piece of honed Belugia limestone on R @parkindustries Pro Edge III #
• Programming a @blancoamerica 441128 sink cutout in a honed Pietra Lavica schist island countertop. #
• The revised “Block Sink Machining Process” page & slideshow just went live -> http://t.co/XYktOExj #WebDesign #SEO #gallery #pix #photos #

Powered by Twitter Tools

• Programming a @blancoamerica 440194 under-counter kitchen sink cutout in a piece of honed Belugia limestone with a Chiseled edge detail. #
• Did a slab layout with a customer, working with another customer on selecting edge details http://t.co/HehGfAkR #
• honing the face a couple of piece of 2cm Belugia limestone that have shop joints. #
• Happy President’s Day! #

Powered by Twitter Tools

• TGIF! #
• Running the last piece of Cosmos now, then a couple pieces of Belugia limestone to be run on the CNC. #
• Got the 1st half of the Belugia limestone island off the CNC just before lunch, got the 2nd half on now. #
• Re-honing pieces of Pietra Lavica now. #
• Chiseling the edge on a couple more pieces of Belugia limestone. #
• Plotting some vinyl templates for a customer layout. #

Powered by Twitter Tools

• Running an OG edge on some Cosmos (beautiful, but flaky soft don’t even call it a granite) material. Very much a pain to work with… #
• The updated Sink slideshow just went live -> http://t.co/YrY4o3oi dropped one bad photo & added 5 new ones. #WebDesign #SEO #
• Re-honing some more pieces of Belugia limestone. #
• Garage door is fixed. #maintenance #
• Gluing up a couple of shop joints on some of the 2cm Belugia limestone countertops. #
• Just finished programming the second half of the honed Belugia limestone. Will run both pieces tomorrow (sink cutout & cooktop cutout). #
• 1 piece of Cosmos left to run tomorrow. No problems with the 3 pieces we ran today. Whew! #

Powered by Twitter Tools

• Got some before & after bathroom shots from a job we did. May use them for a blog post. Definitely going to use some in 1 of R slideshows. #
• NAHB – Builder Confidence Increases for Fifth Consecutive Month in February -> http://t.co/MBBWS6DV via @MarbleInstitute #
• Re-honing the Belugia limestone island pieces now. #
• Cutting a slab of Hillsboro limestone now. #
• Giant Beluga Limestone island getting ready for some edgework. http://t.co/lnJgewrW #

Powered by Twitter Tools

• Our Fireplace Product Showcase slideshow (http://t.co/no4bb9KN ) has been updated & the changes R now live. #webdesign #SEO #
• Now working on R Sink slideshow. This slideshow shows both fabricated sinks we make as well as “off-the-shelf” units from major manufactures #
• Done editing the sink photos, just need to do a few thumbnails & then edit the html <a> & <img> tags. #WebDesign #SCO #gallery #slideshow #
• Flattening the 2 halves of the honed Belugia limestone island. Will re-hone tomorrow. #
• A co-worker got chocolate covered strawberries delivered by Edible Arrangements from her husband. #HappyValentine#039;sDay #

Powered by Twitter Tools

• Block Sink Machining Process -> 1st of our product showcase slideshows 2 B updated & update now live -> http://t.co/e5FQt9bf #webdesign #
• Sending a @PercocoSFC Ubatuba sample board (polished, honed, leathered, carressed, bush-hammered & tuscan finishes) 2 a designer in Reno. #
• Honing out the shop joint in the Belugia limestone island pieces. #
• Just did another template today. #
• Working on our fireplace slideshow now. #
• Cutting some 2cm honed Belugia limestone vanities now. #
• Photos & thumbnails for the fireplace slideshow are done, just need to edit the html <a> & <img> tags. #
• Still have to write the titles for the 9 new images being added to the fireplace slideshow. #Tomorrow #039;sTask #

Powered by Twitter Tools

• Doing an OG Bullnose edge on a couple pieces for a fellow Rocky Mountain Stone Association member. Their CNC is temporarily out of service. #
• Starting to cut some honed Belugia limestone for some kitchen counters. #

Powered by Twitter Tools

• Installers out on a couple jobs today. One is a vanity install the other is a service call to fix what the glass guys messed up. #
• Installing the new seals on the bridge saw table today. Lifting the table/piston out of the hydraulic cylinder now. #

Powered by Twitter Tools