New Trends in Natural Stone

• Installed a new water flow sensor in R CNC. Hope this fixes the problem. #fingersCrossed #maintenance #
• Doing a Full Bullnose edge detail on a piece of honed Belugia limestone on R @parkindustries Pro Edge III #
• Programming a @blancoamerica 441128 sink cutout in a honed Pietra Lavica schist island countertop. #
• The revised “Block Sink Machining Process” page & slideshow just went live -> http://t.co/XYktOExj #WebDesign #SEO #gallery #pix #photos #

Powered by Twitter Tools

• Programming a @blancoamerica 440194 under-counter kitchen sink cutout in a piece of honed Belugia limestone with a Chiseled edge detail. #
• Did a slab layout with a customer, working with another customer on selecting edge details http://t.co/HehGfAkR #
• honing the face a couple of piece of 2cm Belugia limestone that have shop joints. #
• Happy President’s Day! #

Powered by Twitter Tools

• TGIF! #
• Running the last piece of Cosmos now, then a couple pieces of Belugia limestone to be run on the CNC. #
• Got the 1st half of the Belugia limestone island off the CNC just before lunch, got the 2nd half on now. #
• Re-honing pieces of Pietra Lavica now. #
• Chiseling the edge on a couple more pieces of Belugia limestone. #
• Plotting some vinyl templates for a customer layout. #

Powered by Twitter Tools

• Running an OG edge on some Cosmos (beautiful, but flaky soft don’t even call it a granite) material. Very much a pain to work with… #
• The updated Sink slideshow just went live -> http://t.co/YrY4o3oi dropped one bad photo & added 5 new ones. #WebDesign #SEO #
• Re-honing some more pieces of Belugia limestone. #
• Garage door is fixed. #maintenance #
• Gluing up a couple of shop joints on some of the 2cm Belugia limestone countertops. #
• Just finished programming the second half of the honed Belugia limestone. Will run both pieces tomorrow (sink cutout & cooktop cutout). #
• 1 piece of Cosmos left to run tomorrow. No problems with the 3 pieces we ran today. Whew! #

Powered by Twitter Tools

• Got some before & after bathroom shots from a job we did. May use them for a blog post. Definitely going to use some in 1 of R slideshows. #
• NAHB – Builder Confidence Increases for Fifth Consecutive Month in February -> http://t.co/MBBWS6DV via @MarbleInstitute #
• Re-honing the Belugia limestone island pieces now. #
• Cutting a slab of Hillsboro limestone now. #
• Giant Beluga Limestone island getting ready for some edgework. http://t.co/lnJgewrW #

Powered by Twitter Tools

• Doing an OG Bullnose edge on a couple pieces for a fellow Rocky Mountain Stone Association member. Their CNC is temporarily out of service. #
• Starting to cut some honed Belugia limestone for some kitchen counters. #

Powered by Twitter Tools

• Still running pieces of the Golden Crystal #granite on the @parkindustries Pro Edge III. Also starting on the @elkayusa sink cutout program. #
• Leathering a partial slab of limestone, turned out the full slab was not quite big enough for all the pieces we need to cut. #

Powered by Twitter Tools

• Cutting a slab of Golden Crystal #granite for a kitchen. Still waiting on the sink though. #
• Installers are at one job now & headed to another shortly. #
• Running the ¾” Radius edge on R @parkindustries Pro Edge III on the Golden Crystal #granite kitchen countertop pieces. #

Powered by Twitter Tools

• Cut a piece of Tan Brown #granite this morning, now polishing the edge on the @parkindustries Pro Edge III. #
• Re-polished a piece of Calcutta Gold #marble for a table. Will be putting it on the CNC shortly for a OG Bullnose edge detail. #
• Got a pile of returned flyers for @PercocoSFC St. Valentine’s special. #
• Getting ready to leather a limestone slab… #

Powered by Twitter Tools

• 2 guys R headed back to Evergreen. Got a wine room (#leathered Cambrian Black #granite with a Chiseled edge) and some smaller misc pieces. #
• Running the #leathered Betularie #granite powder vanity on the CNC. Finished the OG Bullnose edge, now doing the @Kohler Caxton 2209 cutout. #
• Got a new 1st position Z profile (flat) tool today. Need to send out the 2nd & 3rd positions to get trued up now. #
• Got the invites 2 the 1st Members Meeting (this 1 is open 2 anyone in the industry) of the Rocky Mountain Stone Association ready 2 mail. #

Powered by Twitter Tools